Page – Removing and reinstalling the transfer a Once the new toner cartridge is correctly aligned, you must insert it into the slot until it locks into place, and then close the cover of the slot. RL1 the specified intervals. By continuing to browse, you are agreeing to our use of cookies as explained in our Privacy Policy. The paper size that can A.

Uploader: Gomi
Date Added: 15 February 2006
File Size: 31.38 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 57593
Price: Free* [*Free Regsitration Required]

Solvusoft: Microsoft Gold Certified Company

High-voltage contacts exist around the drum unit. M2 Scanner motor abnormalities mality immediately.

Parameter memory board 2 BK: Using outdated or corrupt Konica Minolta drivers can cause system errors, crashes, and cause your computer or hardware to fail. List of parts to be replaced arbitrarily Named; arbitrarily Count timing KRDS G0 Set the limit value for the parts to be replaced, parts When copy count at the paper exit is completed No. Open the front minota [1]. ADU conveyance path The ADU conveyance path is applicable after the front side copy is completed in the double sided copy mode.

Copy print job 1 Count is made at E Reinstall the above parts following the removal steps in reverse.

List of major differences between the, and List of major differences between the, and Classification Reason Less than Warmup time Less than 19 sec. Fold the copy in half and check to see if the holes are aligned deviation should be within 2mm. In the first step of the replacement procedure, you must open the front door of your Konica Minolta Laser Printer, and then loosen the fixing screw of the developing unit. When the value thus detected at this time is below the initial density recorded in the CPU contained in the CB Main body control boardthe M4 Toner supply motor 1 and the SD9 Toner solenoid are turned on to start to replenish toner up to the specified level of density.


Check the positions of the alignment plate and the paper from the paper exit side.

Loosen the 2 screws [1] and remove the front cover minllta and the front door [3]. The following are included in the return to standard Select the [3. After temporary fastening, use a spring balancer to apply 1. Open the front door [1], and then open the toner supply cover [2].

Remove the 2 stop rings [1] and the bearing [2] on this side, and remove the paper feed roller unit [4] by sliding the bearing [3] on mminolta rear side to the rear.

Rotate the developing input gear counterclock- wise and check the bristle height along the entire surface of the developing sleeve. Fixing Temperature Control, Operation, Cleaning Web Control Once warm-up has completed, the CB switches the L2 and the L3 on and off so that the fixing heat roller can be maintained to the set temperature for idling. Next, you must lift the exhausted drum up and out of the drum unit, and then unpack the replacement component.

Konica Minolta All in One Printer User Guide |

Checking method of the collected data 4. Exposure unit movement in platen mode In platen mode, the scan sequence depends on the copy density minoltz either AE or manual. Using the jig [1] included on the drum unit cover, rotate the drum clockwise and confirm that there are no gaps in the setting powder coat, and that the toner collection sheet and cleaning blade are smooth, etc.


Minoota control board 10 pin 30 pin 2 pin 2 pin 2 pin 15 pin 12 pin 12 pin 36 pin 11 pin FNS CB 3 pin 8 pin. Remove the mminolta screws [3]. Enter the 47 mode. The Konica Minolta is the perfect tool for businesses looking for the smart way to combine all of their document production and management functions inton one simple solution.


Windows XP, Vista, 7, 8, 10 Downloads: Removing and Reinstalling the Developing 71455 A. Remove the 2 screws [3] for each position. Setting method been provided with this machine.

Page 29 List of major differences between the, and List of major differences between the, and Classification Reason Less than Warmup time Less than 19 sec. In the centering adjustment, the centering of the 7.

Open the ADU door [1].